PTI Pavement Repair Products

Concrete Welder Crack Repair 100-Gal Kit

Thu, 29 Jul 2010 00:00:00 -0500

]]>

Concrete Welder™ Crack Repair
(Bulk 100-Gallon Kit)

Contents: 50-Gallons "A" polymer component, 50-Gallons "B" polymer component
Cured Color: Clear/Amber
Concrete Welder™ is available in 10, 30 and 100-gallon kits

DESCRIPTION: Concrete Welder™ Crack Repair rebonds cracked concrete. This thin, penetrating polymer can penetrate into small cracks and forms a high strength adhesive bond between broken structures.

Concrete Welder™ is a low viscosity, fast-reacting urethane polymer which is applied with Vari-Flow dispensing equipment, specially designed for this product. Concrete Welder is recommended for larger highway and other projects where extensive repairs are needed. It can be used with a variety of aggregate materials, depending on the requirements of the specific application. Multiple repairs can be completed in rapid succession with minimal traffic closure time. Concrete Welder is a rapidly-curing polymer used to repair concrete distress and reduces the need for slab cut out and or removal.

Concrete Welder™ is a multi-purpose material that works well for both concrete and asphalt repairs. It allows the user to solve several problems with one material.
Concrete Welder™ will flow underneath cracked or spalled concrete and seal the base against further erosion from water.
Concrete Welder™ acts to waterproof and seal concrete and asphalt from the top to prevent water or other liquids from streaming under the slab and creating voids.
Concrete Welder™ has excellent chemical resistance to oils, hydraulic fluids, gasoline, and salts, and antifreeze.
Concrete Welder™ is also safe to use. It contains no solvents, has no odor, and has low toxicity.

Concrete Welder™ Crack Repair Polymer

INSTRUCTIONS: Concrete Welder performs well in temperature extremes. For best performance, install Concrete Welder at 10°F. to 100°F. ambient temperature and 50-75°F. material temperature. Do not apply during rain or on wet surfaces. Read the Material Safety Data Sheet and all Installation Instructions before using product.

Penetrates and Rebonds

Penetrates and rebonds thin, wide or deep cracks to restore concrete strength.
Seals and Waterproofs, protects from freeze/thaw spalling.
Smooths rough surfaces. Restores a high-traction surface.
Fast repairs and cure. Solidifies in less than 3 minutes. Ready for traffic in 10 minutes.
Repairs successful year round. Repairs in cold or hot weather.
Safe to use, Low Odor Concrete Welder is non-flammable.
There are no peroxides or heavy metals. There is little odor on application, and it is safe to use. See product safety data sheet for more information.
Chemically resistant, resists dilute acids and alkalis. Unaffected by salts, gasoline, diesel fuel, lubricating oils, or antifreeze. Fuel & oil drips from vehicles will not penetrate treated areas.

How do you install Concrete Welder™

Large Crack Repair

Remove loose and unsound material.
Blow crack clean with dry compressed air.
Fill crack with 50 mesh or larger dry sand.
Flood crack with Concrete Welder.
For a skidproof surface, top with dry sand.

Hairline Crack Repair

Blow out cracks with dry compressed air.
Flood with Concrete Welder.
Broadcast with dry sand on uncured liquid for high traction surface.

Spider Cracks

Shot blast or sand blast deck surface.
Flood deck with Concrete Welder at the rate of one gallon per 100 square feet.
Immediately broadcast treated aggregates to refusal into the uncured liquid.
When cured sweep off excess aggregates.

USES:

Concrete Welder™ restores concrete strength for roads, bridges, slabs, parkings structures, roofs and floors. It waterproofs and seals concrete to stop freeze thaw spalling and chemical attack. Concrete Welders thinner viscosity allows the material to penetrate into smaller cracks.

Typical Properties: Application

Components: “A” and “B”
Appearance: A:Clear B:Black
Ratio, A:B, volume 1:1
Viscosity @ 73°F, cps A:24 B:57.5
Specific Gravity @73°F A:1.09 B:1.01
Flash Point, F°. A: 245° B: 360°

Mixed

Pot life, seconds, @ 73°F 60
Cure time, minutes, @ 73°F 10

Typical Cured Properties

Specific Gravity, ASTM, D-792 1.07
Hardness, Durometer D, ASTM, D-2240 70
Tensile Strength, psi , ASTM, D-412 4300
Elongation at Break (%), ASTM, D-412 <10
Tear Strength, ASTM, D-624 275
Compression Strength, psi, ASTM, C-39 4250
Bond strength to PCC, psi 500 (concrete fails cohesively)

Restoring Traffic

With Concrete Welder™ traffic can resume within 10 minutes of completion of work reducing the time of crews exposure to oncoming traffic.

To order, enter the desired QUANTITY in the space below and click Add To Cart. Your Quantity Discount will be automatically calculated.

]]>

Concrete Welder Crack Repair 30-Gal Kit

Thu, 29 Jul 2010 00:00:00 -0500

]]>

Concrete Welder™ Crack Repair
(Bulk 30-Gallon Kit)

Contents: 15-Gallons "A" polymer component, 15-Gallons "B" polymer component
Cured Color: Clear/Amber
Concrete Welder™ is available in 10, 30 and 100-gallon kits

Concrete Welder™ Crack Repair Polymer

Penetrates and Rebonds

Penetrates and rebonds thin, wide or deep cracks to restore concrete strength.
Seals and Waterproofs, protects from freeze/thaw spalling.
Smooths rough surfaces. Restores a high-traction surface.
Fast repairs and cure. Solidifies in less than 3 minutes. Ready for traffic in 10 minutes.
Repairs successful year round. Repairs in cold or hot weather.
Safe to use, Low Odor Concrete Welder is non-flammable.
There are no peroxides or heavy metals. There is little odor on application, and it is safe to use. See product safety data sheet for more information.
Chemically resistant, resists dilute acids and alkalis. Unaffected by salts, gasoline, diesel fuel, lubricating oils, or antifreeze. Fuel & oil drips from vehicles will not penetrate treated areas.

How do you install Concrete Welder™

Large Crack Repair

Remove loose and unsound material.
Blow crack clean with dry compressed air.
Fill crack with 50 mesh or larger dry sand.
Flood crack with Concrete Welder.
For a skidproof surface, top with dry sand.

Hairline Crack Repair

Blow out cracks with dry compressed air.
Flood with Concrete Welder.
Broadcast with dry sand on uncured liquid for high traction surface.

Spider Cracks

Shot blast or sand blast deck surface.
Flood deck with Concrete Welder at the rate of one gallon per 100 square feet.
Immediately broadcast treated aggregates to refusal into the uncured liquid.
When cured sweep off excess aggregates.

USES:

Typical Properties: Application

Components: “A” and “B”
Appearance: A:Clear B:Black
Ratio, A:B, volume 1:1
Viscosity @ 73°F, cps A:24 B:57.5
Specific Gravity @73°F A:1.09 B:1.01
Flash Point, F°. A: 245° B: 360°

Mixed

Pot life, seconds, @ 73°F 60
Cure time, minutes, @ 73°F 10

Typical Cured Properties

Specific Gravity, ASTM, D-792 1.07
Hardness, Durometer D, ASTM, D-2240 70
Tensile Strength, psi , ASTM, D-412 4300
Elongation at Break (%), ASTM, D-412 <10
Tear Strength, ASTM, D-624 275
Compression Strength, psi, ASTM, C-39 4250
Bond strength to PCC, psi 500 (concrete fails cohesively)

Restoring Traffic

With Concrete Welder™ traffic can resume within 10 minutes of completion of work reducing the time of crews exposure to oncoming traffic.

To order, enter the desired QUANTITY in the space below and click Add To Cart. Your Quantity Discount will be automatically calculated.

]]>

Concrete Welder Crack Repair 10-Gal Kit

Tue, 27 Apr 2010 14:59:07 -0500

]]>

Concrete Welder™ Crack Repair
(Bulk 10-Gallon Kit)

Contents: 5-Gallons "A" polymer component, 5-Gallons "B" polymer component
Cured Color: Clear/Amber
Concrete Welder™ is available in 10, 30 and 100-gallon kits

Concrete Welder™ Crack Repair Polymer

Penetrates and Rebonds

Penetrates and rebonds thin, wide or deep cracks to restore concrete strength.
Seals and Waterproofs, protects from freeze/thaw spalling.
Smooths rough surfaces. Restores a high-traction surface.
Fast repairs and cure. Solidifies in less than 3 minutes. Ready for traffic in 10 minutes.
Repairs successful year round. Repairs in cold or hot weather.
Safe to use, Low Odor Concrete Welder is non-flammable.
There are no peroxides or heavy metals. There is little odor on application, and it is safe to use. See product safety data sheet for more information.
Chemically resistant, resists dilute acids and alkalis. Unaffected by salts, gasoline, diesel fuel, lubricating oils, or antifreeze. Fuel & oil drips from vehicles will not penetrate treated areas.

How do you install Concrete Welder™

Large Crack Repair

Remove loose and unsound material.
Blow crack clean with dry compressed air.
Fill crack with 50 mesh or larger dry sand.
Flood crack with Concrete Welder.
For a skidproof surface, top with dry sand.

Hairline Crack Repair

Blow out cracks with dry compressed air.
Flood with Concrete Welder.
Broadcast with dry sand on uncured liquid for high traction surface.

Spider Cracks

Shot blast or sand blast deck surface.
Flood deck with Concrete Welder at the rate of one gallon per 100 square feet.
Immediately broadcast treated aggregates to refusal into the uncured liquid.
When cured sweep off excess aggregates.

USES:

Typical Properties: Application

Components: “A” and “B”
Appearance: A:Clear B:Black
Ratio, A:B, volume 1:1
Viscosity @ 73°F, cps A:24 B:57.5
Specific Gravity @73°F A:1.09 B:1.01
Flash Point, F°. A: 245° B: 360°

Mixed

Pot life, seconds, @ 73°F 60
Cure time, minutes, @ 73°F 10

Typical Cured Properties

Specific Gravity, ASTM, D-792 1.07
Hardness, Durometer D, ASTM, D-2240 70
Tensile Strength, psi , ASTM, D-412 4300
Elongation at Break (%), ASTM, D-412 <10
Tear Strength, ASTM, D-624 275
Compression Strength, psi, ASTM, C-39 4250
Bond strength to PCC, psi 500 (concrete fails cohesively)

Restoring Traffic

With Concrete Welder™ traffic can resume within 10 minutes of completion of work reducing the time of crews exposure to oncoming traffic.

To order, enter the desired QUANTITY in the space below and click Add To Cart. Your Quantity Discount will be automatically calculated.

]]>

Vari-Flo PD 5-15 Polymer Dispenser

Fri, 30 Apr 2010 13:16:52 -0500

]]>

Vari-Flo PD 5-15

Vari-Flo PD 5-15 Polymer Dispenser - 10 or 30 Gallon capacity.

** This item is shipped by common freight carrier. Please contact us directly at 281-778-3223 for a shipping quote.

For use with:

Concrete Welder 10-Gallon and 30-Gallon kits.
and
PolyFlex DS 10-Gallon and 30-Gallon kits.

]]>

Vari-Flo PD 15-50 Polymer Dispenser

Fri, 30 Apr 2010 13:14:40 -0500

]]>

Vari-Flo PD 15-50

Vari-Flo PD 15-50 Polymer Dispenser - 30 or 100 Gallon capacity.

** This item is shipped by common freight carrier. Please contact us directly at 281-778-3223 for a shipping quote.

For use with:

Concrete Welder 30-Gallon and 100-Gallon kits.
and
PolyFlex DS 30-Gallon and 100-Gallon kits.

]]>

PolyFlex DS Twin Dual Cartridge 12-Pack

Sat, 24 Apr 2010 07:53:55 -0500

]]>

PolyFlex DS™ 21 oz. Twin Dual Cartridge (12-Pack)

Polymeric Asphalt & Concrete Repair

Item quantity: 1 case
Case contents: (12) 21 oz. Dual Cartridges with (12) Static Mixer tips.
Shipping weight: 29 lbs.
Available colors: Black or Gray [please select below]

Product Description: PolyFlex DS™ is the polymer only version of FloMix™ and FlexSet™. Use PolyFlex DS when you want a less rigid repair, such as for a traffic loop, control/expansion joint, or for a thin crack repair where deeper penetration is required and a polymeric slurry has too much body. Available in black for asphalt or gray for concrete, PolyFlex DS™ is packaged in 21 oz. Twin Dual Cartridges with 12 cartridges per case. Cartridges can also be purchased individually.

PolyFlex DS™ is also available in convenient 3-gallon case six packs (3 half gallons each of "A" and "B" components) for hand mixed application.
For bulk application, PolyFlex DS™ is available as a 10-gallon kit, 30-gallon kit, or 100-gallon kit for Vari-Flo Polymer Dispenser machine application.

Aggregate may be added where required up to a 3:1 ratio. Cartridge application requires a standard hand operated Dual Cartridge Applicator.

PolyFlex DS (Dopey Soup) is a polymeric version of elastic cement for the repair of concrete and asphalt. When combined with clean dry sand and aggregates, PolyFlex DS forms a high performance, quick-setting, flexible polymer concrete. Within an hour of placement, durable repairs are ready for traffic. PolyFlex DS withstands vibration, heavy traffic loads, and thermal movement. Available in Black and Grey and other colors on special order. Black PolyFlex DS is mixed with clean, dry sand to perform simple, durable repairs in asphalt. Gray PolyFlex DS is used with clean dry sand for concrete repairs. PolyFlex DS is also used in control joints for concrete.

To place an order, enter the Case Quantity desired in the space below and click Add To Cart. Your Quantity Discount will be automatically calculated.

]]>

PolyFlex DS Twin Dual Cartridge 21 oz

Fri, 23 Apr 2010 12:43:57 -0500

]]>

PolyFlex DS™ 21 oz. Twin Dual Cartridge

Polymeric Asphalt & Concrete Repair

Item quantity: (1) 21 oz. Dual Cartridge with (1) Static Mixer tip.
Shipping weight: 3.5 lbs.
Available colors: Black or Gray [please select below]

Product Description: PolyFlex DS™ is the polymer only version of FloMix™ and FlexSet™. Use PolyFlex DS when you want a less rigid repair, such as for a traffic loop, control/expansion joint, or for a thin crack repair where deeper penetration is required and a polymeric slurry has too much body. Available in black for asphalt or gray for concrete, PolyFlex DS™ is packaged in 21 oz. Twin Dual Cartridges. Cartridges can be purchased individually or by the case of 12 cartridges.

PolyFlex DS™ is also available in convenient 3-gallon case six packs (3 half gallons each of "A" and "B" components) for hand application.
For bulk application, PolyFlex DS™ is available as a 10-gallon kit, 30-gallon kit, or 100-gallon kit for Vari-Flo Polymer Dispenser machine application.

Aggregate may be added where required up to a 3:1 ratio. Cartridge application requires a standard hand operated Dual Cartridge Applicator.

PolyFlex DS (Dopey Soup) is a polymeric version of elastic cement for the repair of concrete and asphalt. When combined with clean dry sand and aggregates, PolyFlex DS forms a high performance, quick-setting, flexible polymer concrete. Within an hour of placement, durable repairs are ready for traffic. PolyFlex DS withstands vibration, heavy traffic loads, and thermal movement. Available in Black and Grey and other colors on special order. Black PolyFlex DS is mixed with clean, dry sand to perform simple, durable repairs in asphalt. Gray PolyFlex DS is used with clean dry sand for concrete repairs. PolyFlex DS is also used in control joints for concrete.

To place an order, enter the quantity of cartridges desired in the space below and click Add To Cart. Your Quantity Discount will be automatically calculated.

]]>

Air Operated Dual Cartridge Gun - 300 ml x 300 ml

Wed, 9 Jun 2010 14:38:22 -0500

]]>

Air Operated Dual Cartridge Gun • 300 ml x 300 ml

OVERALL LENGTH: 22”
MAX AIR: 90 psi
RATIO: 1 to 1
THRUSTING FORCE: 1500 lbs. (EXTRA HEAVY DUTY)
WEIGHT: 8.5 lbs.
Shipping Weight: 10.0 lbs.

Aluminum air cylinder is 4" in diameter. Has "air in" and "air out." This provides power forward and power reverse for ease of operation. Supplied with built in air regulator at base of handle. Comes with interchangeable side handle for added stability.

This tool is recommended for use with Concrete Welder and PolyFlex DS Twin Dual Cartridges.

]]>

SlabGasket Expansion Joint Replacement - 1 5/8" (2x4)

Tue, 27 Apr 2010 15:18:09 -0500

]]>

SlabGasket™ Expansion Joint Replacement Solution - 1 5/8" (2x4 Replacement)

SlabGasket™ is designed to replace rotten wood expansion joints in parking lots, driveways, sidewalks, patios, slabs, and pool decks.

SlabGasket™ is used in residential, commercial, and institutional applications.

SlabGasket™ is an extruded, flexible vinyl, the same material used in vinyl shutters, doors, windows, and siding. Immediately effective once installed, no waiting or curing is necessary.

Rapidly installed, blending beautifully with the existing concrete, SlabGasket™ also provides a simple and effective weed-growth deterrent and a cure for trip and fall hazards associated with empty expansion joints.

Click to enlarge

1 5/8" (2x4 Replacement)

Available Colors: Gray, Almond

For rotted "2x4" replacement

1 5/8" Regular

SlabGasket cuts easily with garden pruning shears, a sharp pocket knife, or a box cutter. SlabGasket requires no curing or waiting. Walk or drive on Slab Gasket immediately.

SlabGasket is also available in many other colors and sizes

Order by the foot $3.95 per linear foot.
100' rolls @ $3.88 per linear foot.

Minimum combined order: 3 linear feet
Various lengths and sizes can be combined in your Shopping Cart.

ORDER NOW:

Select the COLOR
Select the SIZE
Select the STYLE
Enter the QUANTITY in LINEAR FEET
Repeat for each Color, Size and/or Style you wish to order.

How do you install SlabGasket?

Installation can be as easy as scratching out the rotten wood and stepping in SlabGasket.

Installation Tip Sheet in Printable format

Do you have unsightly weeds in those cracks and crevices? Are the expansion joints in your paking lot, sidewalk, driveway, patio or pool now rotten or missing? Why not replace them permanently? SlabGasket™ is the perfect and cost effective solution to replace that rotten wood for life.

This 1 5/8” Regular size is designed to replace a rotten 2x4 expansion joint.

To order, select the COLOR, SIZE, STYLE and the QUANTITY in LINEAR FEET in the spaces below and click Add To Cart. Repeat for each Color, Size and/or Style you wish to order.

]]>

4-Seasons Pourable Pothole Filler - Pallet of (36) #5 Kits

Thu, 22 Jul 2010 08:53:09 -0500

]]>

NewLife 4 Seasons™ Pourable Pothole Filler - Pallet of (36) #5 Kits

[CALL FOR BULK PRICING / QUANTITY DISCOUNTS AVAILABLE: 281-778-3223]

Item quantity: (36) #5 Pre-Measured Kits (900 cu/in or ~ 4 liquid Gallons per Kit)
Shipping weight: 1080 lbs.
Cured color: Black

PRODUCT DESCRIPTION: 4 Seasons™ Pourable Pothole Filler is a non-toxic, self-leveling, high bond, rubber-like pourable filler used to permanently seal and repair potholes, wide cracks, and irregularities in asphalt and concrete pavement. Repairs can be made when moisture is present. Just remove standing water and pour.

4 Seasons™ Pourable Pothole Filler does not require any specialized equipment or repair expertise to apply. 4 Seasons™ Pourable Pothole Filler does not require heat and pours easily into the pothole or wide cracks and only takes 30 to 40 minutes to cure. Extensive tests have shown that 4 Seasons™ Pourable Pothole Filler will outlast the surrounding pavement.

4 Seasons™ Pourable Pothole Filler is Guaranteed by the manufacturer to perform; and will stay in place for the life of the surrounding pavement when applied according to the written instructions, or replacement material will be offered.

4 Seasons™ Pourable Pothole Filler will bond to anything including concrete, wood, metal or asphalt.

Click to enlarge

4 Seasons™ Pourable Pothole Filler

A two part blend of liquid asphalt polymers, and aggregate.
Read the Material Safety Data Sheet and all Installation Instructions before using product.

Material Safety Data Sheet - Part 1
Material Safety Data Sheet - Part 2

Easily Repair Potholes and Wide Cracks

Fast repairs and cure. Solidifies in less than 10 minutes. Ready for traffic in 40 minutes.
Non-Hazardous.
Non-Toxic.
Self Priming.
Self Leveling.
Seals and Waterproofs
Repairs successful year round. Repairs in cold or hot weather.
Safe to use, Environmentally friendly recyclable packaging.
No special tools or equiptment required. Mixed easily by hand.

How do you install 4 Seasons™ Pourable Pothole Filler

INSTRUCTIONS: Pothole Repair

Clean pothole area well by sweeping with broom to remove loose grit etc and also standing water.
Pour Liquid into mixing pail, then add aggregate and stir for 40 seconds or until product is liquefied.
Pour 4 Seasons Pothole Filler into pothole. The product is self leveling.
The repair is ready for traffic within 40 minutes; Slightly longer at cooler temperatures.

Wide Crack Repair

Can be used for cracks ranging from ½” on up.
Blow crack clean with leaf blower or compressed air.
Mix according to the instructions in the Installation Tip Sheet
Pour into crack and level off.

Installation Tip Sheet in Printable format

USES:

4 Seasons™ Pourable Pothole Filler is suitable for use on Roads, Highways, Sidewalks, Expansion Joints, Bike Paths, Parking Lots, Tennis Courts, Bridge Decks, Floors, and more. Our customers include DOT's, Asphalt Companies, Sealcoat Companies, Airports, Cement Contractors, Maintenance Crews, Industrial Facilities, Business Owners, and Homeowners.

4 Seasons™ Pourable Pothole Filler

Read All Customer Testimonials

“Repairs have been done in varying weather conditions and this material has not failed”
- City of Dallas Street Services Dept., Texas

“We had been using a fast setting concrete mix, it was time consuming and short lived. Your product is very durable and affordable”
- Allegan County Road Commission, Michigan

“The product performance has proven to me to be far superior than the traditional cold patching”
-5 Star Engineering, P.C, Vermont

“We have been extremely pleased with the results and durability”
- ST Mobile Aerospace Engineering, Inc., Alabama

“We have received positive commentary from the participants of District 4 and agree that your product would be beneficial for use on bridge joints and Vermont roadways.”
- State of Vermont Materials & Research Section, Vermont

Typical Properties: Application

Components: A “Liquid” and B “Aggregate”
Appearance: A:Chocalate Brown B: Off-white, tan, grey, black granules.
Ratio, A:B, volume 1:1 (for pothole repair)
Viscosity @ 73°F, (Brookfield) A:500 to 1000 B: N/A
Specific Gravity @73°F A:1.02 B:2.70
Permeability 0.24 Perme ASTM E-96
Tensile Strength (24 Hrs.) 4000 psi
Meets/Exceeds ASTM D1571/D1572

Mixed

Pot life, minutes, @ 73°F 2
Set time, minutes, @ 73°F 20 to 60 depending on temperature
Mix only the product amount required for your repair. Reseal the remaining product for future use!

Restoring Traffic

With 4 Seasons™ Pourable Pothole Filler traffic can resume within 40 minutes of completion of work reducing the time of crews exposure to oncoming traffic.

To order: Enter the desired item QUANTITY in the space below and click Add To Cart. Your Quantity Discount will be automatically calculated.

]]>

SlabGasket Expansion Joint Replacement (Almond)

Tue, 27 Apr 2010 15:21:21 -0500

]]>

SlabGasket™ Expansion Joint Replacement Solution

SlabGasket™ is designed to replace rotten wood expansion joints in parking lots, driveways, sidewalks, patios, slabs, and pool decks.

SlabGasket™ is used in residential, commercial, and institutional applications.

Click to enlarge

Available Colors: Gray or Almond

SlabGasket Sizes available in Almond:
Regular Sizes
1/2”
3/4”
7/8” - standard (replaces rotted 1x3 or 1x4)
1 1/8”
The most common size is 7/8” standard.

Shorty Sizes*
1/2”
1 1/8”
* If you remove the expansion joint and see concrete underneath then Shorty is the correct product to use.

SlabGasket cuts easily with garden pruning shears, a sharp pocket knife, or a box cutter. SlabGasket requires no curing or waiting. Walk or drive on Slab Gasket immediately.

Order by the foot $2.95 per linear foot.
100' rolls @ $2.88 per linear foot.

Minimum combined order: 4 linear feet
Various lengths and sizes can be combined in your Shopping Cart.

ORDER NOW:

Select the SIZE
Select the STYLE
Enter the QUANTITY in LINEAR FEET
Repeat for each Size and Style you wish to order.

How do you install SlabGasket?

Installation can be as easy as scratching out the rotten wood and stepping in SlabGasket.

Installation Tip Sheet in Printable format

The standard size (7/8”), designed to replace a 1” x 3” or 1” x 4” expansion joint, is the size used by 90% of our customers

To order, select the SIZE, STYLE and the QUANTITY in LINEAR FEET in the spaces below and click Add To Cart. Repeat for each Size and Style you wish to order.

]]>

Static Mixer - Extra Dispensing Tip

Tue, 27 Apr 2010 14:11:39 -0500

]]>

Disposable Static Mixer Dispensing Tips

For use with Concrete Welderâ¢ and PolyFlex DSâ¢ 21 oz. Twin Dual Cartridges.

When you order Concrete Welderâ¢ or Polyflex DSâ¢ 21 oz. Twin Dual Cartridges you receive (1) Static Mixer for each cartridge ordered.

** This item is only for ordering ADDITIONAL Static Mixers. **

To order, enter the desired QUANTITY in the space below and click Add To Cart.

]]>

Hand Operated Dual Cartridge Gun - 300 ml x 300 ml

Fri, 23 Apr 2010 12:49:19 -0500

]]>

Hand Operated Dual Cartridge Gun • 300 ml x 300 ml

OVERALL LENGTH: 14 1/8”
MECHANICAL ADVANTAGE: 24 to 1
RATIO: 1 to 1
THRUSTING FORCE: 850 lbs. (EXTRA HEAVY DUTY)
WEIGHT: 3 lbs.
Shipping Weight: 6.0 lbs.

Uses 3/8" case hardened rods and cam. All three rods, push the washers for added ease of dispensing product. Supplied with side handle for added stability. Handle can be used on either side.

This tool is recommended for use with Concrete Welder and PolyFlex DS Twin Dual Cartridges.

]]>

4-Seasons Pourable Pothole Filler

Thu, 22 Jul 2010 08:52:21 -0500

]]>

NewLife 4 Seasons™ Pourable Pothole Filler

[CALL FOR PRICES / QUANTITY DISCOUNTS AVAILABLE: 281-778-3223]

Coverage: #5 Pre-Measured Kit fills 900 cu/in or ~ 4 liquid Gallons)
Cured color: Black

4 Seasons™ Pourable Pothole Filler will bond to anything including concrete, wood, metal or asphalt.

Click to enlarge

4 Seasons™ Pourable Pothole Filler

A two part blend of liquid asphalt polymers, and aggregate.
Read the Material Safety Data Sheet and all Installation Instructions before using product.

Material Safety Data Sheet - Part 1
Material Safety Data Sheet - Part 2

Easily Repair Potholes and Wide Cracks

Fast repairs and cure. Solidifies in less than 10 minutes. Ready for traffic in 40 minutes.
Non-Hazardous.
Non-Toxic.
Self Priming.
Self Leveling.
Seals and Waterproofs
Repairs successful year round. Repairs in cold or hot weather.
Safe to use, Environmentally friendly recyclable packaging.
No special tools or equiptment required. Mixed easily by hand.

How do you install 4 Seasons™ Pourable Pothole Filler

INSTRUCTIONS: Pothole Repair

Clean pothole area well by sweeping with broom to remove loose grit etc and also standing water.
Pour Liquid into mixing pail, then add aggregate and stir for 40 seconds or until product is liquefied.
Pour 4 Seasons Pothole Filler into pothole. The product is self leveling.
The repair is ready for traffic within 40 minutes; Slightly longer at cooler temperatures.

Wide Crack Repair

Can be used for cracks ranging from ½” on up.
Blow crack clean with leaf blower or compressed air.
Mix according to the instructions in the Installation Tip Sheet
Pour into crack and level off.

Installation Tip Sheet in Printable format

USES:

4 Seasons™ Pourable Pothole Filler

Read All Customer Testimonials

Typical Properties: Application

Components: A “Liquid” and B “Aggregate”
Appearance: A:Chocalate Brown B: Off-white, tan, grey, black granules.
Ratio, A:B, volume 1:1 (for pothole repair)
Viscosity @ 73°F, (Brookfield) A:500 to 1000 B: N/A
Specific Gravity @73°F A:1.02 B:2.70
Permeability 0.24 Perme ASTM E-96
Tensile Strength (24 Hrs.) 4000 psi
Meets/Exceeds ASTM D1571/D1572

Mixed

Pot life, minutes, @ 73°F 2
Set time, minutes, @ 73°F 20 to 60 depending on temperature
Mix only the product amount required for your repair. Reseal the remaining product for future use!

Restoring Traffic

With 4 Seasons™ Pourable Pothole Filler traffic can resume within 40 minutes of completion of work reducing the time of crews exposure to oncoming traffic.

To order: Enter the desired item QUANTITY in the space below and click Add To Cart. Your Quantity Discount will be automatically calculated.

]]>

Concrete Welder 21 oz. Twin Dual Cartridge

Wed, 21 Apr 2010 17:47:20 -0500

]]>

Concrete Welder™ 21 oz. Twin Dual Cartridge

Item quantity: (1) 21 oz. Dual Cartridge with (1) Static Mixer tip.
Shipping weight: 3.5 lbs.
Cured color: Clear/Amber

PRODUCT DESCRIPTION: Concrete Welder™ rebonds cracked concrete. This thin, penetrating polymer is applied from 21 oz. Twin Dual Cartridges. Concrete Welder™ restores concrete strength by penetrating and rebonding fine cracks. Large cracks are sand or aggregate filled then saturated with Concrete Welder™ to form a high strength polymer concrete. Application requires a standard hand operated Dual Cartridge Applicator.

Concrete Welder™ is a thin, low viscosity, rapidly-curing polymer used to repair concrete distress and reduces the need for slab cut out and or removal.

Concrete Welder™ is also available in 10, 30 and 100-gallon kits that are applied with a proportioning dispensing unit. For Professional and Industrial use only. Please contact us for 10, 30 and 100-gallon kit pricing.

Concrete Welder™ Polymer

Penetrates and Rebonds

Penetrates and rebonds thin, wide or deep cracks to restore concrete strength.
Seals and Waterproofs, protects from freeze/thaw spalling.
Smooths rough surfaces. Restores a high-traction surface.
Fast repairs and cure. Solidifies in less than 3 minutes. Ready for traffic in 10 minutes.
Repairs successful year round. Repairs in cold or hot weather.
Safe to use, Low Odor Concrete Welder is non-flammable.
There are no peroxides or heavy metals. There is little odor on application, and it is safe to use. See product safety data sheet for more information.
Chemically resistant, resists dilute acids and alkalis. Unaffected by salts, gasoline, diesel fuel, lubricating oils, or antifreeze. Fuel & oil drips from vehicles will not penetrate treated areas.

How do you install Concrete Welder™

Hairline Crack Repair

Blow out cracks with dry compressed air.
Flood with Concrete Welder.
Broadcast with dry sand on uncured liquid for high traction surface.
(Coverage approximatley 50 linear feet at 1/4” x 1/4”)

Large Crack Repair

Remove loose and unsound material.
Blow crack clean with dry compressed air.
Fill crack with 50 mesh or larger dry sand.
Flood crack with Concrete Welder.
For a skidproof surface, top with dry sand.

Spider Cracks

Shot blast or sand blast deck surface.
Flood deck with Concrete Welder at the rate of one gallon per 100 square feet.
Immediately broadcast treated aggregates to refusal into the uncured liquid.
When cured sweep off excess aggregates.

USES:

Concrete Welder™ restores concrete strength for roads, bridges, slabs, parking structures, roofs and floors. It waterproofs and seals concrete to stop freeze thaw spalling and chemical attack. Concrete Welders thinner viscosity allows the material to penetrate into smaller cracks.

Typical Properties: Application

Components: “A” and “B”
Appearance: A:Clear B:Black
Ratio, A:B, volume 1:1
Viscosity @ 73°F, cps A:24 B:57.5
Specific Gravity @73°F A:1.09 B:1.01
Flash Point, F°. A: 245° B: 360°

Mixed

Pot life, seconds, @ 73°F 60
Cure time, minutes, @ 73°F 10

Typical Cured Properties

Specific Gravity, ASTM, D-792 1.07
Hardness, Durometer D, ASTM, D-2240 70
Tensile Strength, psi , ASTM, D-412 4300
Elongation at Break (%), ASTM, D-412 <10
Tear Strength, ASTM, D-624 275
Compression Strength, psi, ASTM, C-39 4250
Bond strength to PCC, psi 500 (concrete fails cohesively)

Restoring Traffic

With Concrete Welder™ traffic can resume within 10 minutes of completion of work reducing the time of crews exposure to oncoming traffic.

To order, enter the desired QUANTITY in the space below and click Add To Cart. Your Quantity Discount will be automatically calculated.

]]>

Concrete Welder Twin Dual Cartridge 12-Pack

Tue, 27 Apr 2010 11:40:51 -0500

]]>

Concrete Welder™ 21 oz. Twin Dual Cartridges
(12 Pack )

Item quantity: 1 Case
Case contents: (12) 21 oz. Dual Cartridges with (12) static mixer tips.
Shipping weight: 29 lbs.
Cured Color: Clear/Amber

Concrete Welder™ is a thin, low viscosity, rapidly-curing polymer used to repair concrete distress and reduces the need for slab cut out and or removal.

Concrete Welder™ Polymer

Penetrates and Rebonds

Penetrates and rebonds thin, wide or deep cracks to restore concrete strength.
Seals and Waterproofs, protects from freeze/thaw spalling.
Smooths rough surfaces. Restores a high-traction surface.
Fast repairs and cure. Solidifies in less than 3 minutes. Ready for traffic in 10 minutes.
Repairs successful year round. Repairs in cold or hot weather.
Safe to use, Low Odor Concrete Welder is non-flammable.
There are no peroxides or heavy metals. There is little odor on application, and it is safe to use. See product safety data sheet for more information.
Chemically resistant, resists dilute acids and alkalis. Unaffected by salts, gasoline, diesel fuel, lubricating oils, or antifreeze. Fuel & oil drips from vehicles will not penetrate treated areas.

How do you install Concrete Welder™

Large Crack Repair

Remove loose and unsound material.
Blow crack clean with dry compressed air.
Fill crack with 50 mesh or larger dry sand.
Flood crack with Concrete Welder.
For a skidproof surface, top with dry sand.

Hairline Crack Repair

Blow out cracks with dry compressed air.
Flood with Concrete Welder.
Broadcast with dry sand on uncured liquid for high traction surface.

Spider Cracks

Shot blast or sand blast deck surface.
Flood deck with Concrete Welder at the rate of one gallon per 100 square feet.
Immediately broadcast treated aggregates to refusal into the uncured liquid.
When cured sweep off excess aggregates.

USES:

Typical Properties: Application

Components: “A” and “B”
Appearance: A:Clear B:Black
Ratio, A:B, volume 1:1
Viscosity @ 73°F, cps A:24 B:57.5
Specific Gravity @73°F A:1.09 B:1.01
Flash Point, F°. A: 245° B: 360°

Mixed

Pot life, seconds, @ 73°F 60
Cure time, minutes, @ 73°F 10

Typical Cured Properties

Specific Gravity, ASTM, D-792 1.07
Hardness, Durometer D, ASTM, D-2240 70
Tensile Strength, psi , ASTM, D-412 4300
Elongation at Break (%), ASTM, D-412 <10
Tear Strength, ASTM, D-624 275
Compression Strength, psi, ASTM, C-39 4250
Bond strength to PCC, psi 500 (concrete fails cohesively)

Restoring Traffic

With Concrete Welder™ traffic can resume within 10 minutes of completion of work reducing the time of crews exposure to oncoming traffic.

To order, enter the desired Case QUANTITY in the space below and click Add To Cart. Your Quantity Discount will be automatically calculated.

]]>

SlabGasket Expansion Joint Replacement (Gray)

Tue, 27 Apr 2010 15:20:07 -0500

]]>

SlabGasket™ Expansion Joint Replacement Solution

SlabGasket™ is designed to replace rotten wood expansion joints in parking lots, driveways, sidewalks, patios, slabs, and pool decks.

SlabGasket™ is used in residential, commercial, and institutional applications.

Click to enlarge

Available Colors: Gray or Almond

SlabGasket Sizes available in Gray:
Regular Sizes
1/2”
3/4”
7/8” - standard (replaces rotted 1x3 or 1x4)
1 1/8”
The most common size is 7/8” standard.

Shorty Sizes*
3/4”
7/8” - standard
* If you remove the expansion joint and see concrete underneath then Shorty is the correct product to use.

SlabGasket cuts easily with garden pruning shears, a sharp pocket knife, or a box cutter. SlabGasket requires no curing or waiting. Walk or drive on Slab Gasket immediately.

Order by the foot $2.95 per linear foot.
100' rolls @ $2.88 per linear foot.

Minimum combined order: 4 linear feet
Various lengths and sizes can be combined in your Shopping Cart.

ORDER NOW:

Select the SIZE
Select the STYLE
Enter the QUANTITY in LINEAR FEET
Repeat for each Size and Style you wish to order.

How do you install SlabGasket?

Installation can be as easy as scratching out the rotten wood and stepping in SlabGasket.

Installation Tip Sheet in Printable format

]]>

Motorized Pail Mixer

Thu, 22 Apr 2010 10:54:23 -0500

]]>Motorized Pail Mixer

This heavy duty Motorized Pail Mixer is engineered specifically for use with FloMix Flowable Asphalt Repair and FlexSet Rapid Concrete Repair materials.

For larger projects, the use of a Motorized Pail Mixer will greatly increase the speed and efficiency of the installation process and allows the installer improved productivity and reduced labor costs.

Shipping Weight: 100 Lbs.
Gearmotor Â½ HP - 115V â 8.3 amp
This item qualifies for FREE SHIPPING with any wholesale pallet purchase of FloMix or FlexSet pavement repair materials.
]]>

Topping Aggregate 50 lbs

Thu, 15 Oct 2009 09:57:18 -0500

]]>Additional Coated Topping Aggregate (Bulk)
WEIGHT: 50 lbs.
COLOR: Asphalt Black or Concrete Gray [please select below]

For use with FloMix Flowable Asphalt Repair kits, FlexSet Rapid Concrete Repair kits, and PolyFlex DS (Dopey Soup) applications.

FloMix Asphalt and FlexSet Concrete pre-measured kits already include Coated Topping Aggregate.
This item is for ordering additional bulk quantities only.

To order this product:
Select the color desired from the options below.
Enter the quantity desired in the space below and click Add To Cart. Your Quantity Discount will be automatically calculated.
]]>

PolyFlex DS 10-Gallon Kit

Tue, 27 Apr 2010 14:58:09 -0500

]]>

PolyFlex DS Asphalt & Concrete Repair Polymer

Available colors: Black, Grey

PolyFlex DS (Dopey Soup) is a hand-mixed version of Elastic Cement for the repair of concrete and asphalt. This flexible, high-strength, epoxy-like product reacts slowly enough to be mixed by hand, yet unlike epoxy, cures quickly. PolyFlex DS 10-Gallon Kits are supplied in two 5 gallon containers (5 gallon container of "A" and a 5 gallon container of "B" components). PolyFlex DS is also available in convenient six packs (3 half gallons each of "A" and "B"). Combined with clean dry sand and aggregates, PolyFlex DS forms a high performance, quick-setting, flexible polymer concrete. Within an hour of placement, durable repairs are ready for traffic. PolyFlex DS withstands vibration, heavy traffic loads, and thermal movement. Available in black and gray and other colors on special order. Black PolyFlex DS is mixed with clean, dry sand to perform simple, durable repairs in asphalt. Gray PolyFlex DS is used with sand for concrete repairs. PolyFlex DS is also used in control joints for concrete.

To place an order, enter the quantity of kits desired in the space below and click Add To Cart. Your Quantity Discount will be automatically calculated.
]]>

PolyFlex DS 3-Gallon Kit

Thu, 22 Apr 2010 12:11:44 -0500

]]>

PolyFlex DS Asphalt & Concrete Repair Polymer

Available colors: Black or Gray [please select below]

PolyFlex DS (Dopey Soup) 3-gallon kit is a hand-mixed version of Elastic Cement for the repair of concrete and asphalt. This flexible, high-strength, epoxy-like product reacts slowly enough to be mixed by hand, yet unlike epoxy, cures quickly. PolyFlex DS is supplied in convenient six packs (3 half gallons each of "A" and "B" components). Combined with clean dry sand and aggregates, PolyFlex DS forms a high performance, quick-setting, flexible polymer concrete. Within an hour of placement, durable repairs are ready for traffic. PolyFlex DS withstands vibration, heavy traffic loads, and thermal movement. Available in Black and Grey and other colors on special order. Black PolyFlex DS is mixed with clean, dry sand to perform simple, durable repairs in asphalt. Gray PolyFlex DS is used with sand for concrete repairs. PolyFlex DS is also used in control joints for concrete.

To place an order, enter the quantity of kits desired in the space below and click Add To Cart. Your Quantity Discount will be automatically calculated.
]]>

FlexSet Rapid Concrete Repair 3-Gal Kit

Thu, 17 Dec 2009 11:07:51 -0600

]]>

FlexSet Rapid Concrete Repair 3-Gal Kit

Coverage: 3-Gal FlexSet Kit fills 0.2 cubic feet
Cured color: Concrete Gray

FLEXSET™ Rapid Concrete Repair is a high performance rapid cure repair polymer supplied in three and five gallon kits for the restoration and reconstruction of deteriorated or damaged concrete without expensive concrete extraction machinery and debris removal. Simple to use, FLEXSET™ is used to patch, restore, and repair concrete potholes, narrow or wide cracks, spalls, break-out, joint openings, and floor restorations. Repairs support load, restore aggregate interlock, improve ride, and blend in visually with the surrounding pavement. Just remove excess dirt and debris from the surface and then pour. When applied, FlexSet™ has a 9 to 12 minute work time and a 1 hour cure time; and can be successfully applied at ANY temperature, including sub-zero repair. No Material Extraction Required! Save on equipment and labor costs!

Engineered to withstand extremely heavy loads from commercial aircraft traffic, heavy truck traffic, and general highway use, FLEXSET™ also provides a simple and effective alternative for general purpose pavement repair and pavement preservation projects.

Key Advantages:
Creates durable, long-lasting repairs
Seals and waterproofs
Provides smooth, high-traction surface
Requires no dig out !!
Repairs precisely to-grade - Snowplow friendly
Odorless and vapor less
Unaffected by water, fuel, solvents, or oil
Unaffected by hot or cold temperatures
Easily repairs wide and narrow cracks, potholes, spalls, breaks, and damaged areas
Reliable Results Easily Achieved!
Ready for traffic in 1 hour with minimal preparation required

Common Applications:
Potholes
Parking Lots
Driveways
Bridges
Roadways
Sub-Floors
Slabs
Ramps
Loading Docks
Warehouse Floors
Post Anchors
Trip Hazards, and many more...

FLEXSET™ Repairs Are Guaranteed To Outlast The Surrounding Pavement
View the FlexSet Photo Gallery.
Watch the Video Demonstration.

Department of Transportation Approved By Material Labs and Maintenance Departments For Our U.S. Airports, Highways, Bridges and Roads. FLEXSET™ Provides A Long Term Load Bearing Rapid Repair Solution For Your Concrete Restoration Needs.

To place an order, enter the quantity of kits desired in the space below and click Add To Cart. Your Quantity Discount will be automatically calculated.

]]>

FloMix Pourable Asphalt Repair 3-Gal Kit

Thu, 17 Dec 2009 11:08:56 -0600

]]>

FloMix Pourable Asphalt Repair 3-Gal Kit

Coverage: 3-Gal FloMix Kit fills 0.2 cubic feet
Cured color: Asphalt Black

FLOMIX™ Pourable Asphalt is a rapid asphalt repair supplied in three and five gallon kits for reconstruction of deteriorated asphalt with NO ASPHALT REMOVAL. FLOMIX™ is used to permanently restore and repair asphalt potholes, alligatoring, cracking, raveling, and surface compaction (ruts). Stops reflective cracking! Repairs support load, restore aggregate interlock, improve ride, and blend in visually with the surrounding pavement. Just remove excess dirt and debris from the surface and then pour. When applied, FloMix™ has a 9 to 12 minute work time and a 1 hour cure time; and can be successfully applied at ANY temperature, including sub-zero repair. No Material Extraction required! Save on equipment and labor costs!

Engineered to withstand extremely heavy loads from commercial aircraft traffic, heavy truck traffic, and general highway use, FLOMIX™ also provides a simple and effective alternative for general purpose asphalt repair and pavement preservation projects.

Key Advantages:
Creates durable, long-lasting repairs
Seals and waterproofs
Provides smooth, high-traction surface
Requires no dig out !!
Repairs precisely to-grade - Snowplow friendly
Odorless and vapor less
Unaffected by water, fuel, solvents, or oil
Unaffected by hot or cold temperatures
Easily repairs wide and narrow cracks, potholes, alligatored asphalt
Reliable Results Easily Achieved!
Ready for traffic in 1 hour with minimal preparation required

Common Applications:
Potholes
Parking Lots
Driveways
Bridges
Roadways
Sub-Floors
Slabs
Ramps
Loading Docks
Warehouse Floors
Post Anchors
Trip Hazards, and many more...

FLOMIX™ Repairs Are Guaranteed To Outlast The Surrounding Pavement
View the FloMix Photo Gallery.
Watch the Video Demonstration.

Department of Transportation Approved By Material Labs and Maintenance Departments For Our U.S. Airports, Highways, Bridges and Roads. FLOMIX™ Provides A Long Term Load Bearing Rapid Repair Solution For Your Asphalt Restoration Needs.

To place an order, enter the quantity of kits desired in the space below and click Add To Cart. Your Quantity Discount will be automatically calculated.

]]>

FlexSet Rapid Concrete Repair - Pallet of (48) 3-Gal

Thu, 5 Nov 2009 17:23:01 -0600

]]>FLEXSET™ Rapid Concrete Repair is a high performance rapid cure repair polymer supplied in three and five gallon kits for the restoration and reconstruction of deteriorated or damaged concrete without expensive concrete extraction machinery and debris removal. Simple to use, FLEXSET™ is used to patch, restore, and repair concrete potholes, narrow or wide cracks, spalls, break-out, joint openings, and floor restorations. Repairs support load, restore aggregate interlock, improve ride, and blend in visually with the surrounding pavement. Just remove excess dirt and debris from the surface and then pour. When applied, FlexSet™ has a 9 to 12 minute work time and a 1 hour cure time; and can be successfully applied at ANY temperature, including sub-zero repair. No Material Extraction Required! Save on equipment and labor costs!

Common Applications:
Potholes
Parking Lots
Driveways
Bridges
Roadways
Sub-Floors
Slabs
Ramps
Loading Docks
Warehouse Floors
Post Anchors
Trip Hazards, and many more...

FLEXSET™ Repairs Are Guaranteed To Outlast The Surrounding Pavement
View the FlexSet Photo Gallery.
Watch the Video Demonstration.

Department of Transportation Approved By Material Labs and Maintenance Departments For Our U.S. Airports, Highways, Bridges and Roads. FLEXSET™ Provides A Long Term Load Bearing Rapid Repair Solution For Your Concrete Restoration Needs.

* Commercial, Industrial, or Public Works customers interested in establishing credit terms may complete a PO Account Application. Your account representative will contact you within 1 business day. Please call or contact us with any additional details for expedited service.

To place an order, enter the quantity of palettes desired in the space below and click Add To Cart. Your Quantity Discount will be automatically calculated.

]]>

FloMix Flowable Asphalt Repair - (48) 3-Gal Kits

Thu, 5 Nov 2009 17:23:57 -0600

]]>FLOMIX™ Flowable Asphalt Repair is a rapid asphalt repair supplied in three and five gallon kits for reconstruction of deteriorated asphalt with NO ASPHALT REMOVAL. FLOMIX™ is used to permanently restore and repair asphalt potholes, alligatoring, cracking, raveling, and surface compaction (ruts). Stops reflective cracking! Repairs support load, restore aggregate interlock, improve ride, and blend in visually with the surrounding pavement. Just remove excess dirt and debris from the surface and then pour. When applied, FloMix™ Flowable Asphalt Repair has a 9 to 12 minute work time and a 1 hour cure time; and can be successfully applied at ANY temperature, including sub-zero repair. No Material Extraction required! Save on equipment and labor costs!

Key Advantages:
Creates durable, long-lasting repairs
Seals and waterproofs
Provides smooth, high-traction surface
Requires no dig out !!
Repairs precisely to-grade - Snowplow friendly
Odorless and vapor less
Unaffected by water, fuel, solvents, or oil
Unaffected by hot or cold temperatures
Easily repairs wide and narrow cracks, potholes, alligatored asphalt
Reliable Results Easily Achieved!
Ready for traffic in 1 hour with minimal preparation required

Common Applications:
Potholes
Parking Lots
Driveways
Bridges
Roadways
Sub-Floors
Slabs
Ramps
Loading Docks
Warehouse Floors
Post Anchors
Trip Hazards, and many more...

FLOMIX™ Flowable Asphalt Repairs Are Guaranteed To Outlast The Surrounding Pavement
View the FloMix Photo Gallery.
Watch the Video Demonstration.

Department of Transportation Approved By Material Labs and Maintenance Departments For Our U.S. Airports, Highways, Bridges and Roads. FLOMIX™ Asphalt Repair Provides A Long Term Load Bearing Rapid Repair Solution For Your Asphalt Restoration Needs.

* Commercial, Industrial, or Public Works customers interested in establishing credit terms may complete a PO Account Application. Your account representative will contact you within 1 business day. Please call or contact us with any additional details for expedited service.

To place an order, enter the quantity of pallets desired in the space below and click Add To Cart. Your Quantity Discount will be automatically calculated.

]]>

FlexSet Rapid Concrete Repair - Pallet of (36) 5-Gal

Tue, 13 Apr 2010 11:04:55 -0500

Common Applications:
Potholes
Parking Lots
Driveways
Bridges
Roadways
Sub-Floors
Slabs
Ramps
Loading Docks
Warehouse Floors
Post Anchors
Trip Hazards, and many more...

FLEXSET™ Repairs Are Guaranteed To Outlast The Surrounding Pavement
View the FlexSet Photo Gallery.
Watch the Video Demonstration.

Department of Transportation Approved By Material Labs and Maintenance Departments For Our U.S. Airports, Highways, Bridges and Roads. FLEXSET™ Provides A Long Term Load Bearing Rapid Repair Solution For Your Concrete Restoration Needs.

* Commercial, Industrial, or Public Works customers interested in establishing credit terms may complete a PO Account Application. Your account representative will contact you within 1 business day. Please call or contact us with any additional details for expedited service.

To place an order, enter the quantity of palettes desired in the space below and click Add To Cart. Your Quantity Discount will be automatically calculated.

]]>

FloMix Flowable Asphalt Repair - (36) 5-Gal Kits

Tue, 13 Apr 2010 11:06:31 -0500

Key Advantages:
Creates durable, long-lasting repairs
Seals and waterproofs
Provides smooth, high-traction surface
Requires no dig out !!
Repairs precisely to-grade - Snowplow friendly
Odorless and vapor less
Unaffected by water, fuel, solvents, or oil
Unaffected by hot or cold temperatures
Easily repairs wide and narrow cracks, potholes, alligatored asphalt
Reliable Results Easily Achieved!
Ready for traffic in 1 hour with minimal preparation required

Common Applications:
Potholes
Parking Lots
Driveways
Bridges
Roadways
Sub-Floors
Slabs
Ramps
Loading Docks
Warehouse Floors
Post Anchors
Trip Hazards, and many more...

FLOMIX™ Flowable Asphalt Repairs Are Guaranteed To Outlast The Surrounding Pavement
View the FloMix Photo Gallery.
Watch the Video Demonstration.

]]>

Pail Mixer - EggBeater

Thu, 6 May 2010 20:39:41 -0500

]]>(1) “Egg Beater” Style Mixer / Mixing Tool / Pail Mixer / Mud Mixer.

This mixing paddle is 5” in diameter, with a 7/16” x 30” steel hex shaft.

This plated solid steel mixer is the perfect tool for use with FlexSet™ Concrete Patch and FloMix™ Asphalt Patch 5-Gal and 3-Gal Kits. The tool provides excellent results, with minimum torque strain for the user and low to no aeration of the material being mixed. Ideal for sheetrock mud, thin sets, paints, grouts and concrete products. Fits on any standard 1/2” or larger drill and will fit some 3/8” drills. Long 30” shaft reduces lower back strain.
Cleanup is easy and quick!
]]>

FlexSet Rapid Concrete Repair 5-Gal Kit

Sat, 6 Feb 2010 14:50:50 -0600

]]>

FlexSet Rapid Concrete Repair 5-Gal Kit

Coverage: 50 sq/ft at 1/8"; Volume .4 cubic feet
Cured color: Concrete Gray

FLEXSET™ Rapid Concrete Repair is a high performance rapid cure repair polymer supplied in three and five gallon kits for the restoration and reconstruction of deteriorated or damaged concrete without expensive concrete extraction machinery and debris removal. Simple to use, FLEXSET™ Rapid Concrete Repair is used to patch, restore, and repair concrete potholes, narrow or wide cracks, spalls, break-out, joint openings, and floor restorations. Repairs support load, restore aggregate interlock, improve ride, and blend in visually with the surrounding pavement. Just remove excess dirt and debris from the surface and then pour. When applied, FlexSet™ has a 9 to 12 minute work time and a 1 hour cure time; and can be successfully applied at ANY temperature, including sub-zero repair. No Material Extraction Required! Save on equipment and labor costs!

Engineered to withstand extremely heavy loads from commercial aircraft traffic, heavy truck traffic, and general highway use, FLEXSET™ also provides a simple and effective alternative for general purpose pavement repair and pavement preservation projects.

Common Applications:
Potholes
Parking Lots
Driveways
Bridges
Roadways
Sub-Floors
Slabs
Ramps
Loading Docks
Warehouse Floors
Post Anchors
Trip Hazards, and many more...

FLEXSET™ Repairs Are Guaranteed To Outlast The Surrounding Pavement
View the FlexSet Photo Gallery.
Watch the Video Demonstration.

Department of Transportation Approved By Material Labs and Maintenance Departments For Our U.S. Airports, Highways, Bridges and Roads. FLEXSET™ Provides A Long Term Load Bearing Rapid Repair Solution For Your Concrete Restoration Needs.

To place an order, enter the quantity of kits desired in the space below and click Add To Cart. Your Quantity Discount will be automatically calculated.

]]>

FloMix Pourable Asphalt Repair 5-Gal Kit

Sat, 6 Feb 2010 14:52:06 -0600

]]>

FloMix Pourable Asphalt Repair 5-Gal Kit

Coverage: 50 sq/ft at 1/8"; Volume .4 cubic feet
Cured color: Asphalt Black

FLOMIX™ Pourable Asphalt Repair is a rapid asphalt repair supplied in three and five gallon kits for reconstruction of deteriorated asphalt with NO ASPHALT REMOVAL. FLOMIX™ Pourable Asphalt Repair is used to permanently restore and repair asphalt potholes, alligatoring, cracking, raveling, and surface compaction (ruts). Stops reflective cracking! Repairs support load, restore aggregate interlock, improve ride, and blend in visually with the surrounding pavement. Just remove excess dirt and debris from the surface and then pour. When applied, FloMix™ has a 9 to 12 minute work time and a 1 hour cure time; and can be successfully applied at ANY temperature, including sub-zero repair. No Material Extraction required! Save on equipment and labor costs!

Engineered to withstand extremely heavy loads from commercial aircraft traffic, heavy truck traffic, and general highway use, FLOMIX™ also provides a simple and effective alternative for general purpose asphalt repair and pavement preservation projects.

Key Advantages:
Creates durable, long-lasting repairs
Seals and waterproofs
Provides smooth, high-traction surface
Requires no dig out !!
Repairs precisely to-grade - Snowplow friendly
Odorless and vapor less
Unaffected by water, fuel, solvents, or oil
Unaffected by hot or cold temperatures
Easily repairs wide and narrow cracks, potholes, alligatored asphalt
Reliable Results Easily Achieved!
Ready for traffic in 1 hour with minimal preparation required

Common Applications:
Potholes
Parking Lots
Driveways
Bridges
Roadways
Sub-Floors
Slabs
Ramps
Loading Docks
Warehouse Floors
Post Anchors
Trip Hazards, and many more...

FLOMIX™ Repairs Are Guaranteed To Outlast The Surrounding Pavement
View the FloMix Photo Gallery.
Watch the Video Demonstration.

Department of Transportation Approved By Material Labs and Maintenance Departments For Our U.S. Airports, Highways, Bridges and Roads. FLOMIX™ Provides A Long Term Load Bearing Rapid Repair Solution For Your Asphalt Restoration Needs.

To place an order, enter the quantity of kits desired in the space below and click Add To Cart. Your Quantity Discount will be automatically calculated.

]]>

PTI Pavement Repair Products

Concrete Welder Crack Repair 100-Gal Kit

Concrete Welder™ Crack Repair (Bulk 100-Gallon Kit)

Concrete Welder™ Crack Repair Polymer

Penetrates and Rebonds

How do you install Concrete Welder™

USES:

Typical Properties: Application

Mixed

Typical Cured Properties

Restoring Traffic

Concrete Welder Crack Repair 30-Gal Kit

Concrete Welder™ Crack Repair (Bulk 30-Gallon Kit)

Concrete Welder™ Crack Repair Polymer

Penetrates and Rebonds

How do you install Concrete Welder™

USES:

Typical Properties: Application

Mixed

Typical Cured Properties

Restoring Traffic

Concrete Welder Crack Repair 10-Gal Kit

Concrete Welder™ Crack Repair (Bulk 10-Gallon Kit)

Concrete Welder™ Crack Repair Polymer

Penetrates and Rebonds

How do you install Concrete Welder™

USES:

Typical Properties: Application

Mixed

Typical Cured Properties

Restoring Traffic

Vari-Flo PD 5-15 Polymer Dispenser

Vari-Flo PD 5-15

Vari-Flo PD 15-50 Polymer Dispenser

Vari-Flo PD 15-50

PolyFlex DS Twin Dual Cartridge 12-Pack

PolyFlex DS™ 21 oz. Twin Dual Cartridge (12-Pack)

PolyFlex DS Twin Dual Cartridge 21 oz

PolyFlex DS™ 21 oz. Twin Dual Cartridge

Air Operated Dual Cartridge Gun - 300 ml x 300 ml

Air Operated Dual Cartridge Gun • 300 ml x 300 ml

SlabGasket Expansion Joint Replacement - 1 5/8" (2x4)

SlabGasket™ Expansion Joint Replacement Solution - 1 5/8" (2x4 Replacement)

1 5/8" (2x4 Replacement)

Available Colors: Gray, Almond

Order by the foot $3.95 per linear foot. 100' rolls @ $3.88 per linear foot.

How do you install SlabGasket?

4-Seasons Pourable Pothole Filler - Pallet of (36) #5 Kits

NewLife 4 Seasons™ Pourable Pothole Filler - Pallet of (36) #5 Kits

[CALL FOR BULK PRICING / QUANTITY DISCOUNTS AVAILABLE: 281-778-3223]

4 Seasons™ Pourable Pothole Filler

Easily Repair Potholes and Wide Cracks

How do you install 4 Seasons™ Pourable Pothole Filler

USES:

4 Seasons™ Pourable Pothole Filler

Typical Properties: Application

Mixed

Restoring Traffic

SlabGasket Expansion Joint Replacement (Almond)

SlabGasket™ Expansion Joint Replacement Solution

Order by the foot $2.95 per linear foot. 100' rolls @ $2.88 per linear foot.

How do you install SlabGasket?

Static Mixer - Extra Dispensing Tip

Hand Operated Dual Cartridge Gun - 300 ml x 300 ml

Hand Operated Dual Cartridge Gun • 300 ml x 300 ml

4-Seasons Pourable Pothole Filler

NewLife 4 Seasons™ Pourable Pothole Filler

[CALL FOR PRICES / QUANTITY DISCOUNTS AVAILABLE: 281-778-3223]

4 Seasons™ Pourable Pothole Filler

Easily Repair Potholes and Wide Cracks

How do you install 4 Seasons™ Pourable Pothole Filler

USES:

4 Seasons™ Pourable Pothole Filler

Typical Properties: Application

Mixed

Restoring Traffic

Concrete Welder 21 oz. Twin Dual Cartridge

Concrete Welder™ 21 oz. Twin Dual Cartridge

Concrete Welder™ Polymer

Penetrates and Rebonds

Concrete Welder™ Crack Repair
(Bulk 100-Gallon Kit)

Concrete Welder™ Crack Repair
(Bulk 30-Gallon Kit)

Concrete Welder™ Crack Repair
(Bulk 10-Gallon Kit)

Order by the foot $3.95 per linear foot.
100' rolls @ $3.88 per linear foot.

Order by the foot $2.95 per linear foot.
100' rolls @ $2.88 per linear foot.

Concrete Welder™ 21 oz. Twin Dual Cartridges
(12 Pack )

Order by the foot $2.95 per linear foot.
100' rolls @ $2.88 per linear foot.